Sales - Rental - Service

All photos and drawings are for illustration only.
Note: All scaffolding and accessories must be assembled and used in accordance with applicable ANSI and OSHA,

state and local safety regulations. Do not use this product in areas where user can come in contact with power.

End Frame Characteristics

Frame Lock Types Available

Pins

Wall Tie Brace

Cat-A-Corner Braces

Wall Tie Brace With Clamp (36”L Size)……….WT-36………11#
Wall Tie Brace With Clamp (48”L Size)…….…WT-48………15#

[Options for Attaching Inserts image]
There is a charge for attaching inserts at the factory.

Insert attached using spring rivet……………….ATINSR
Insert attached using roll pin……………………..ATINRP
Insert attached using rivet & cotter key……..ATINRC
Insert attached using welded rivet……………..ATINWE

5’ end panel w/toeboard……………………..(*)GRZ5E…………..34#
42” end panel w/toeboard…………………..(*)GRZ42E…………32#
Guard rail mid post easy w/o toeboard clip…(*)GZMH……5#
Guard rail mid post easy w/toeboard clip…….(*)GZMHTC..9#
Note: specify tube size A, B, or C (*)

7’ side panel…………………………………………GRZ7S………………..12#
8’ side panel…………………………………………GRZ8S………………..14#
10’ side panel……………………………………….GRZ10S………………17#

Pins

Base Plate Rigid 4” Stem………………………..(*)-BPR…………..3#
Base Plate Swivel 4” Stem………………………(*)-BPS……………4#

Leveling Jack Rigid…………………………………..(*)-LJR………….12#
Leveling Jack Swivel…………………………………(*)-LJS………….12#
Leveling Jack Extention……………………………(*)-LJX………….12#
Note: specify tube size A, B or C (*)

8” Caster 4” Stem W/Snap Pin

Wall Tie Brace

5’W x 2’H…....(*)-FS52-(*)…..23#
5’W x 3’H…....(*)-FS53-(*)…..25#
5’W x 4’H…....(*)-FS54-(*)…..31#
5’W x 4’6”…...(*)-FS546-(*)…35#
5’W x 5’H……..(*)-FS55-(*).....39#
5’W x 6’H……..(*)-FS56-(*)…..43#
5’W x 6’4”H….(*)-FS564-(*)…53#
5’W x 6’6”H….(*)-FS566-(*)…52#

Replacement Parts

1” Collar…………(*)IN………1#
1/8” Collar………(**)IN......1#
3/16” Collar…….(B)INSC….1#
Without Collar………..(B)INX…….1#


Example: Specify (*) tube size. A is 1 ½”, B is 1-5/8”, C is 1.69” Frames.

Other collar thicknesses available – contact factory

Replacement Parts

Frames & Lock Types
• Frames are manufactured of high-strength structural steel tubing with I.D. coated tube.
• Finish: Powder coated with UV protection. High pressure phosphate wash/rinse
• Baked at high temperatures for increased durability.
• Standard colors are black or yellow (Available in other colors at additional cost.)
• Compatible with ALL major scaffold brands.

Straddle Braces

Frames

7’ Brace-24-3/4” Locking Spacing…..…..BS7H27……….15#
8’ Brace-27-3/4” Locking Spacing……….BS8H27…….16.5#
10’ Brace-27-3/4” Locking spacing……..BS10H27……..19#


7’ Brace-36” Lock Spacing…………………..BS7H36……….15#
8’ Brace-36” Lock Spacing…………………..BS8H36…….16.5#
10’ Brace-36” Lock Spacing…………………BS10H36……..19#

7’ Brace-48” Lock Spacing…………………..BS7H48……….15#
8’ Brace – 48” Lock Spacing………………..BS8H48…….16.5#
10’ Brace-48” Lock Spacing………………..BS10H48…..….19#

Base Plate, Guard Rail & Side Bracket

7’ Spacing – 27-3/4” Lock Spacing…….B7H27…..…..12#
8’ Spacing – 27-3/4” Lock Spacing…….B8H27.......13.6#
10’ Spacing – 24-3/4” Lock Spacing…..B10H27…..16.7#

7’ Spacing – 24” Lock Spacing……………B7H24……….12#
8’ Spacing – 24” Locking Spacing……….B8H24…...13.6#
10’ Spacing – 24” Lock Spacing………….B10H24….16.7#

7’ Spacing – 36” Lock Spacing……………B7H36……...12#
8’ Spacing – 36” Lock Spacing……………B8H36…….13.6#
10’ Spacing – 36” Lock Spacing………….B10H36….16.7#

7’ Spacing – 48” Lock Spacing……………B7H48……….12#
8’ Spacing – 48” Lock Spacing……………B8H48…...13.6#
10’ Spacing – 48” Lock Spacing…………B10H48…..16.7#

7’ Spacing – 36” & 48” Lock Spacing….B7H3648………12#
10’ Spacing – 36” & 48” Lock Spacing…B10H3648..16.7#

Guard Rail System – Easy (Recommended for Rolling Towers)

• Superior quality sealed ball bearing and roller bearing wheel.
• Protected grease zerks are easy to locate on both wheel and swivel.
• Wheel and swivel brakes.

Caster 8” Cast Iron Wheel……..Cap. 500#............(*)-C8……….14#
Caster 8” Plaster Wheel ………..Cap. 500#............(*)-CP8……….9#
                                      (With non-marking tread)
Note: Specify Tube Size A,B, or C (*)

Rigid Parallel Tube Clamp……………….CPT…………………..1.5#
Lever Tail Nut…………………………………LN……………………..1#
Half Clamp W/Stud & Wing Nut……..CST……………………1#
Thumb Screw……………………….…………TS……………………..3#
Leveling Jack Clamp………………………..LJC…………………….1#
Gooser Slide……………………………………GS……………………..1#

Outrigger 30” Wide………………..(*)OR…………………..15#
Note: Specify tube size A, B, or C (*)

Guard Rail System – Easy (Recommended for Rolling Towers)

Outrigger

Saddle hanger type 20”…………………………(*)SB20H……….10#
Saddle hanger type 24”…………………………(*)SB24H……….11#
Saddle hanger type 30”…………………………(*)SB30H……….12#

Angle hanger type 20”…………………………..(*)SB20A……….10#
Angle hanger type 24”…………………………..(*)SB24A……….11#
Angle hanger type 30”…………………………..(*)SB30A……….12#

End & side hanger type 20”…………………..(*)SB20E………..12#
End & side hanger type 24”…………………..(*)SB24E………..13#
End & side hanger type 30”…………………..(*)SB30E………..14#

Saddle hanger adj. type 20”-30”……………(*)SB2030J……..14#

Side bracket/Guard Rail-Angle Hanger....SBGR20C…………19#
End guard rail for side bracket*…………….SBGRD…………….20#
*(Adjustable 20” – 30”)

Clamp-on adjustable side bracket………….(*)SB2030JCL….16#
Clamp-on side bracket 20”…………………….(*)SB20CL……….12#
Clamp-on side bracket 24”…………………….(*)SB24CL……….13#
Clamp-on side bracket 30”…………………….(*)SB30CL……….14#
Note: specify tube size A, B, or C (*)

It All Starts With A Phone Call

Toll-free 877-221-4020

Scaffolding - Swing Stages​ 

Braces & Casters

Cat-A-Corner Braces

Two Way Shore Head


(4” & 8” with two carriage bolts)……………..SHH-2W…….…9#
4” J Shore Head………………………………………..SHH-J4…………6#

Straddle Braces

Base Plate, Guard Rail & Side Bracket

8” Caster 4” Stem W/Snap Pin

Hangers & Brackets

Scaffolding​

For 5’W x 7’L Tower……………(*)BC57…………….13#
For 5’W x 8’L Tower……………(*)BC58…………….16#
For 5’W x 10’L Tower………….(*)BC510………….20#
Note: Specify Tube size A, B or C (*)
Other cat-a-corner and lateral brace sizes are available – contact factory.

Fastening Pins

Safety Equipment